Notice Système d'enceintes Pioneer S-31C-QL

Pioneer

Description

Notice utilisateur, mode d'emploi du modèle 'S-31C-QL' de marque 'Pioneer'

Informations

• Publié par: shuij
• Nombre de lectures: 90
• Langue: Français
• Poids de l'ouvrage: 6 Mo

Extrait

cover_31C.fm 1 ページ ２００９年７月２９日　水曜日　午後５時５０分
S-31C-K
S-31C-QL /
/
1
En
???B??BD?qL???S-31C_En.fm 2 ページ ２００９年７月２９日　水曜日　午後４時１６分
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the
instructions, put them away in a safe place for future reference.
Caution: in use
? Do not place the speaker on an unstable surface. It could Before you start
present a hazard if it falls, as well as damaging the equipment.
• The nominal impedance of this speaker system is 6 Ω.
? Do not use the speaker to output distorted sound for long Connect the speaker system to an amplifier with a load
periods of times. This can result in a fire hazard.impedance ranging from 4 Ω to 16 Ω (a model with “4 Ω to
16 Ω” displayed on the speaker output terminals). ? Do not sit or stand on the speaker, or let children play on the
speaker.In order to prevent damage to the speaker system resulting
from input overload, please observe the following precautions: ? Do not put large or heavy objects on top of the speaker.
? Do not supply power to the spea ker system in excess of the
maximum permissible input. Cleaning the speaker cabinet
? When using a graphic equalizer to emphasize loud sounds With normal use, wiping with a dry cloth should be sufficient to
in the high-frequency range, do not use excessive amplifier keep the cabinet clean. If necessary, clean with a cloth dipped in
volume. a neutral cleanser diluted five or six times with water, and wrung
out well. Do not use furniture wax or cleansers.Do not try to force a low-powered amplifier to produce loud
volumes of sound (the amplifier’s harmonic distortion will Never use thinners, benzine, insecticide sprays or other chemicals
be increased, and you may damage the speaker). on or near this unit since these will corrode the surfaces.
Caution: installation
? Do not attach these speakers to the wall or ceiling. They may What’s in the boxfall off and cause injury.
Speaker cable (3 m) x 1? Do not install your speakers overhead on the ceiling or wall. If
improperly attached, the speaker grille can fall and cause Silicon rubber foot x 4
damage or personal injury.
? Switch off and unplug your AV equipment and consult the
instructions when connecting up components. Make sure you
Warranty carduse the correct connecting cables.
Operating instructions (this document)
For U.S. model
WARNING: Handling the cord on this product or
cords associated with accessories sold with the
product will expose you to chemicals listed on
proposition 65 known to the State of California and
other governmental entities to cause cancer and
birth defect or other reproductive harm.
Wash hands after handling D36-P4_A_En
For European model
If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used
electronic products in accordance with legislation that requires proper treatment, recovery and recycling.
Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to
designated collection facilities or to a retailer (if you purchase a similar new one).
For countries not mentioned above, please contact your local authorities for the correct method of disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential
negative effects on the environment and human health. K058_A_En
2
En
?English
S-31C_En.fm 3 ページ ２００９年７月２９日　水曜日　午後４時１６分
When using the silicon rubber feet
These speaker systems have been provided with silicon rubber How to install
feet. Use them to adjust the four corners to produce optimum
stability.
Choosing where to place the speaker systems Using the template (see end page) will allow easiest adjustment of
the setting angle.? Sounds played through speaker systems are easily affected in
subtle ways by the conditions in the listening space.
? For best sound, choose a solid floor upon which to place the Using the template
speakers, and position the speakers as shown below. The level
1 Open the hole in the template along the line indicating of low sounds can be adjusted by moving the speakers closer
your desired setting angle.to or further from the wall. Adjust the speakers so that they are
equidistant from their respective side walls to assure balanced 2 Align the line with the front of the unit, and then align
sound. the template with the cabinet.
? If the room has a lot of reverberation, we recommend hanging
heavy fabric on the walls, and/or putting a carpet on the floor
to damp the sound. For best results, cover walls completely.
? This speaker is a bookshelf-type speaker which will give best
performance when placed on a solid, level surface off the floor.
Placing the speaker directly on the floor will result in boomy,
undefined sound.
3 Affix the four silicon rubber feet in alignment with the
four cut-out holes.
0 5101520
50 cm
11(19 /16 in.)
20 cm
7(7 /8 in.)
Attaching and Removing the Grille
It is recommended that this speaker system be used with the grille
net attached, but it can be removed if desired. To remove, follow
these instructions:
1 To remove the grille, place your fingers at the outside of
the grille toward the bottom and pull gently outward. Then
? Pioneer assumes no liability whatsoever for damages do the same at the top to detach.
resulting from assembly, improper mounting, insufficient
2 To reattach the grille, hold the speaker grille with the reinforcement, misuse of the product, acts of nature, etc.
triangular symbol pointing upward, then align the four pins
on the back side of the grille with the holes in the speaker
Using the Foam Plug and press in firmly.
On the rear side of the unit, a foam plug is provided to allow
adjustment of the bass sound. The foam plug can be removed if
desired to produce a different bass emphasis.
The following can be taken as general guidelines for use of the
foam plug:
? Mounted in the middle of a rack : Leave the foam plug in place
? Mounted on the top of a rack or on the floor: Remove the foam
plug
foam plug
Do not force the foam plug into the hole excessively,
since it might be pressed inside the speaker and be
impossible to remove.
3
EnS-31C_En.fm 4 ページ ２００９年７月２９日　水曜日　午後４時１６分
Connections
This speaker does not include speaker cables used for connecting
to an amplifier.
Connecting the cables
1 Switch off the power to your amplifier.
2 Connect the speaker cables to the input terminals on the
back of the speaker. For input terminal polarity, red is
positive (+) and black is negative (–).
Loosen the knobs on the input terminals and insert the speaker
cable wires into each of the terminal post holes, then tighten the
knobs.
(+)Red terminal
(−)Black terminal
Common-side
speaker cord
Hot-side speaker cord
3 Connect the other ends of the cables to the amp's speaker
output terminals (for more details, refer to your amp
instruction manual).
? You can also connect the spea ker’s terminals with a banana
plug.
? When using a banana plug, first remove the caps covering the
speaker terminal.
? After connecting the plugs, pull lightly on the cables to make
sure that the ends of the cables are securely connected to the
terminals. Poor connections can create noise and
interruptions in the sound.
? If the cables’ wires happen to be pushed out of the terminals,
allowing the wires to come into contact with each other, it
places an excessive additional load on the amp. This may
cause the amp to stop functioning, and may even damage the
amp.
? When using a set of speakers connected to an amplifier, you
won’t be able to obtain the normal stereo effect if the polarity
(+, –) of one of the speakers (left or right) is reversed.
CAUTION
These speaker terminals carry HAZARDOUS LIVE
voltage. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts. D3-4-2-2-3_A_En
4
EnEnglish
S-31C_En.fm 5 ページ ２００９年７月２９日　水曜日　午後４時１６分
Specifications
Specifications and design subject to possible modification
Enclosure. . . . . . . . . . . . . . . . . . . . . . . . . . . . Bass-reflex bookshelf type
without notice, due to improvements.
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-way
Woofer . . . . . . . . . . . . 10 cm (4 in.) cone x 2
Tweeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 cm (1 in.) dome
Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Ω is a trademark placed on a product with Pioneer’s Phase
Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Hz to 40 kHz Control technology. This technology enables high-grade sound
Sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 dB (2.83 V) reproduction through each component by improving overall
Maximum input power . . .