Funk-o-politan Hat Sized to fit an average adult head Materials: 1 ...

Tricot Ramwools

Sujets

• Tricot
• Laine
• Loisir créatif
• Patron

Informations

• Publié par: DoItYourself
• Nombre de lectures: 77
• Langue: English

Extrait

Funk-o-politan Hat

Sized to fit an average adult head

Materials:

1 skein Cascade Softspun

180m/197yds

2 buttons.

Needles:

4.5mm (US 7) and 6mm (US 10)

40cm circular. 6mm (US 10) double point set

Tension:

15 sts = 4” in pattern stitch on 6mm

(US 10) needles.

With 4.5mm (US 7) circular needles, cast on

100 sts. Join into round and work in K1, P1

rib for 10 rounds.

Work short row shaping for the peak of the

hat as follows:

K1, P1 for 72 sts. Wrap the next st as follows:

Bring yarn to front. Slip next st knitwise.

Bring yarn to back. Slip the slipped st back to

the left hand needle. Turn to the wrong side.

K1, P1 for 44 sts. Wrap the next st as before.

Turn to the right side.

K1, P1 for 38 sts. Wrap the next st as before.

Turn to the wrong side.

K1, P1 for 32 sts. Wrap the next st as before.

Turn to the right side.

K1, P1 for 26 sts. Wrap the next st as before.

Turn to the wrong side.

K1, P1 for 20 sts. Wrap the next st as before.

Turn to the right side.

Resume working in K1, P1 to the beginning of

the round. When you come to a slipped st,

pick up the yarn wrapper at its base and work

it together with the slipped st. This will

prevent a hole forming at the places where

the work was turned. Work 10 more rounds,

working the remaining slipped sts together

with their wrappers as you encounter them.

Change to 6mm (US 10) circular needles.

Work a foundation row for the pattern stitch

as follows:

*K1, yo, K1, P2* Repeat between *'s to end of

round. 125 sts.

Begin Lace Rib Pattern

Round 1, 2 and 3: *K3, P2* Repeat between *

to end of round.

Round 4: *K2tog, yo, K1, P2* Repeat between

* to end of round.

Round 5, 6 and 7: as Round 1.

Round 8: *K1, yo, SSK, P2* Repeat between *

to end of round.

Repeat these 8 rounds 7 times.

Decrease as follows:

Work Rounds 1 to 3 in Lace Rib.

Next Round: *K2tog, yo, K1, P2tog* Repeat

between * to end of round. 100 sts

Next 2 Rounds: *K3, P1* Repeat between * to

end of round.

Next Round: *K2tog, yo, SSK* Repeat

between * to end of round. 75 sts

Next Round: K to end of round.

Next Round: *K2tog, K1* Repeat between * to

end of round. 50 sts.

Next Round: K to end of round.

Next Round: *yo, SSK* Repeat between * to

end of round.

Next Round: *K2tog* Repeat between * to

end of round. 25 sts.

Next Round: K to end of round.

Next Round: *K2tog* Repeat between * to

last st. K1. 13 sts. Break yarn. With a darning

needle, pass yarn tail through all sts and

draw closed.

Make I-cord band for front of hat as follows:

With two 6mm (US 10) double point needles,

cast on 4 sts. *K4 then

without turning to the

wrong side

, slide these 4 sts to the opposite

end of the needle. Pull the yarn tightly from

the end of the row to the beginning of the

row and K4.* Repeat between * until I-cord

measures 8”. Cast off.

Finishing: Cut peak stiffening out of a pop

bottle, margarine tub or other light plastic

container, using the template below. Fold the

ribbing in half to the inside of the hat and

sew 28 sts of the cast on edge to 28 sts of

the last round of ribbing on either side of the

beginning of the round for a total of 56 sts

sewn at the centre back of the hat. Insert the

peak stiffening into the fold and sew the

remaining sts of the cast on edge to the last

round of ribbing, stretching the ribbing

lengthwise to fit over the widest point of the

peak. Centre the I-cord band over the peak of

hat and sew in place. Attach 2 buttons to

each end of the I-cord. Darn in yarn ends.