This product carries the CE mark which indicates conformity with the European Directive on Electromagnetic Compatibility (EMC Directive 89/336/EEC) and the European Low Voltage Directive (LVD 73/23/EEC), as amended. It also conforms with European Directives on Telecommunications Terminal Equipment and Satellite Earth Stations (TTE-SES Directive 98/13/EC)
Plantronics Ltd Interface Business Park Bincknoll Lane Wootton Bassett Wiltshire SN4 8QQ ENGLAND Tel: + 44 1793 842200 Fax:+ 44 1793 848853
Hovedsætindgang Kuulokkeen liitäntä Prise du microcasque Headset-Buchse Attacco per la cuffia Hodesettinngang
IMPORTANT
Porta do Microauscultador Puerto del auricular Headsetuttag Compatibility Switches Compatibiliteit Schakelaars Kompatibilitetsomskiftere Yhteensovituskytkimet Commutateurs de configuration Konfigurationsschalter Regolazione della sintonia Kompatibilitetsbrytere Selectores de Compatibilidade Conmutadores de compatibilidad Kompatibilitetsom-kopplare
Headset Stand Headset Houder Hovedsætholder Kevytkuuloketeline Porte-microcasque Headset-Ständer Gancio di supporto per la cuffia Hodesettholder Apoio do Microauscultador Soporte para el auricular Headsethållare
Accessory Port Aansluitpunt Accessoires Tilbehørsindgang Lisävarusteiden liitäntä Prise pour accessoire Zubehör-Anschlussbuchse Attacco per gli accessori Inngang for tilleggsutstyr Entrada de Acessórios Soporte para el auricular Puerto para accesorios Uttag för extra tillbehör
aaier r
eher
rafusos or
4
5
INSTRUCTIONS
PREPARING THE REMOTE PACK
1 2 3
4
Charge for a minimum of 1 hour before first use.
1
ART INSTALLATION
wing:
2 inches) away from any computer es monitors in close proximity which
between the CA20 Adapter
n between the CA20 Adapter
, contact the Plantronics Customer
E UNIT
t as shown. Connect the Base Unit (B) al power supply.
REGISTRATION OF THE BASE UNIT AND REMOTE PACK
(Fig. 3)
INSTRUCTIONS
1Once the remote unit is fully charged, plug in your chosen Plantronics headset to the port (19). 2Re-dock your remote pack into the base unit. 3Push down the tone control switch (18), and hold for 5 seconds before releasing. The on-line LED on the base unit will flash (17). 4Press the mute button on the remote pack (15) and hold for 5 seconds before releasing. If the registration of the remote unit to the base unit has been successful, the ‘on-line’ buttons on the remote (17) and the base unit (17) will be illuminated, within 60 seconds. The LED illumination will be intermittent on the remote (17) and permanent on the base unit (17).
If the LED’s are not illuminated in this way, repeat the process.
ESTABLISHING COMPATIBILITY
The CA20 Adapter is supplied with it’s compatibility switches set to work with 90% of telephones. If however, you do not get a dial tone when lifting your receiver, please follow these steps:
1and compatibility switch 2 to position 1 (20).Set compatibility switch 1 to position A 2listen for a dial tone. If there is no tone, repeat the steps below for theLift your receiver and
SETTING THE VOLUME LEVELS
1
2
3
USING THE CA20 ADAPTER
1
7
lected by using the tone control ssing the tone control switch will the setting to 'treble . A third ’ epress the headset/handset pter, however, as you approach go beyond the useable range of e 3 short warning beeps in seconds, and the nits will turn off. Any calls and the Ready/On-Line sumed. dset as follows: repeated every 30 seconds 0 seconds
ps
emote pack by docking it in the e battery is fully recharged, the
NG
nit’s battery is charging.
After the batteries have been and you may notice a hen this occurs, the remote ent battery pack, part number te using the special tool. Dispose r dispose of batteries in a fire.
e unit has not become er base unit by removing and pack, and by un-plugging and unit AC Adapter Plug andset switch so that the above the switch connected to the base unit. connected to the mains supply. or on the base unit is illuminated perly connected to the remote 9). Check: your telephone is e unit’s telephone port. nected to the base unit’s n switch settings (20)
beeps. Walk back into range
by placing the remote unit in ) to check headset compatibility (15) on the remote unit. 6) should then turn off lume (12) on the base unit n switch settings on the