Notice et mode d'emploi du lave-vaisselle Fisher & Paykel modèle DD24

Fisher & Paykel

Description

Notice utilisateur, mode d'emploi du modèle 'DD24' de marque 'Fisher & Paykel'

Sujets

• Lave-vaisselle

Informations

• Publié par: muthor
• Nombre de lectures: 917
• Langue: Français
• Poids de l'ouvrage: 6 Mo

Extrait

Integrated panel preparation DD24STI and DD24DTI models DishDrawer Préparation du panneau intégré Modèles DD24STI et DD24DTI DishDrawer AC SU

SUC A                Safety and warnings Cut Hazard   WARNING! Take care - panel edges are sharp. Failure to use caution could result in injury or cuts. Important! Read these instructions completely and carefully. Ensure the product is not plugged in. Installation of DishDrawer® panels requires basic mechanical and electrical skills. Installation must comply with your local building and electricity regulations. Failure to install the DishDrawer panels correctly could invalidate any warranty or liability claims.

Contents Double models      Product preparation          Single models       Product preparation     Panel Installation       Badge cut-out, handle and panel bracket    Securing the panel brackets     Reconnecting the wires and fitting the  panels and a custom toe kick  (double models only)        Important! SAVE THESE INSTRUCTIONS The models shown in this user guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our local website listed on the back cover or contact your local Fisher & Paykel dealer. 2 4 6 7 8 1 SUC A

SUC A 2 rPdocu tperaparit Double DishDrawer models C 5 A ⁄1 i 6 r ”  g (8 ap mm)  A on D  .nim 1⁄16”  (2   mm) B t h o ei e  g ki h c t  k o   f  lenap min.  ½ “ (12 mm)  Installation diagrams for illustration purposes only The following calculations assume the top of the upper panel is aligned with the top of the adjacent cabinetry. The � nal panel/cabinetry alignment is achieved by adjusting the feet: width of ALL panels Measure A (the width between adjacent door/drawer fronts) and write it in the � rst box below, then complete the equation. A door clearancepanel width A door clearancewidth ALL panels eg   24  ¼ ”      - 2 x 1⁄8   ”       = 24 1⁄1   6”                       - 2 x     =     (616 mm)               (2.5 mm)         (611 mm) (min. 1⁄8” (2.5 mm) )(min. 23 7⁄16”  (595 mm) ) height of upper panel standard height B upp h e e r i   g p h a t n   el B door extension height upper panel eg 17 3⁄8”      + 0 ”       =     17 3⁄8”                  17 3⁄8”                   +     = (442 mm)          (0 mm)          (442 mm) (442 mm) (0 mm recommended) height of lower panel Measure C (door/drawer height (or equivalent)) and write it in the � rst box below, then complete the equation. C upp h e e r i   g p h a t n   ellow h e e r i   g p h a t  nel Cheight upper panelheight lower panel eg 30 ”         - 17 3⁄8”      - 5⁄16”    = 12 5⁄16”                        -                    -      5⁄16”    = (8 mm) (762 mm)         (442 mm)       ( A 8 i   r m ga m p )         (312 mm) (min. 30 ” (762 mm)  + B)) Air gap (min. 12  ¼ ”   (311.5 mm) ) Note: The ‘door extension’ B allows for the top of the upper panel to be above the DishDrawer® where required.

 rPdocu trpperataoin 3 Toe kick preparation height of toe kick panel Measure D (height from the top of adjacent cabinet door fronts to the � oor) and write it in the � rst box below, then complete the equation. height DB toe k h i e c i k g  p ht a   nel DB toe kick panel eg 34 ¼ ”       - 0”      - 30 11⁄16”    -  ½ ”      = 3 1⁄8”                 -                          - (   7 3   7   0   9       1   1 m   ⁄   1   6   m   ”   )     -    (    1    2       ½       m   ”    m    )      = (870 mm)(0 mm)(779 mm)(12 mm)(79 mm) hei c g a h b t  i a n d e j t a r c y ent  ext d e o n o si r on Di d s i h m D e r n a si w o e n r® clea m r i a n n .  ce 2 5⁄8”   ( (7 m 0 i .5 n   . mm) ) Toe kick options   The black prefinished toe kick panel is  supplied. This panel can also have a front panel of your choice attached to it using screws or an adhesive.   A toe kick panel of any material with thickness  3⁄8 -    ¾ ”   (9 - 19 mm) can be screwed to the plastic toe kick panel bracket (supplied). (43 1 2 7 m ” m) (5 2 5  3 m ⁄16 m ” )(43 R 2      ½ m   ” m   ) Integrated Panel material max. 2 5⁄8” - 5”   5⁄8 -   13⁄16”   (16 - 20 mm) panel thickness 2 5⁄8” (67mm) (67-127 mm)   Adequately sealed to withstand moisture (122 O F/50 O C @ 80% RH) Parts supplied Toe kick lenap screws (5) s P c a r n e e w l  s p  ( a 1 n 2 e ) l  Integrated door seal (2) ( I S n a t t e i g n r   a c t h e r d o  r m e e c   t s a u n p g p u li l e ar d   ) badge (2) b T r o a e c  k k i e c t k     ( p 1) anel  Panel bracket (2) Prefinished Toe kick panel (1) SUC A

A sledom rewarDhsiD elgniS noitaraperp tcudorP 4  .nim 1⁄16”  (2   mm) B 3 A ⁄8 ir ”    ( g 9 a m p m)   3 A ⁄8 ir ”    ( g 9 a m p m)   Installation diagrams for illustration purposes only The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry. width of the panel Measure A (the width between adjacent door/drawer fronts) and write it in the � rst box below, then complete the equation. A door clearancepanel width A door clearancepanel width eg  24  ¼ ”      - 2 x 1⁄8 ”       = 24 1⁄1 6”                      - 2 x     =     (616 mm)               (2.5 mm)         (611 mm) (min. 1⁄8” (2.5 mm) )(min. 23 7⁄16”  (595 mm) ) height of the panel Measure B (door/drawer height (or equivalent)) and write it in the � rst box below, then complete the equation. B panel height B panel height eg 17 ¾ ”       - 3⁄8”    = 17 3⁄8”      - 3⁄8”   (9 mm)   Air gap    = (451 mm)      (9 mm)         (442 mm) (min. 17 3⁄8” (442 mm) ) Air gap Note: when the top of the DishDrawer® has to be lower than the adjacent cabinetry, the panel can be increased in height. AC SU

 Product preparation 3⁄8”  (9mm)   3⁄8”  (9mm)   Air gap Air gap Integrated Panel material   5⁄8 -   13⁄16”   (16 - 20 mm) panel thickness   Adequately sealed to withstand moisture (122 O F/50 O C @ 80% RH) Parts supplied Panel panel screws (6) Integrated door seal (1) ( I S n a t t e i g n r   a c t h e r d o  r m e e c   t s a u n p g p u li l e ar d   ) badge (1) Panel bracket (1) 5 SUC A

SUC A 6 Badge cut-out, handle and panel bracket Installation diagrams feature double models for illustration purposes only 1 Important! Ensure the product is not plugged in 2 1 2 1 4 3

  3 4 1 1 Seucir 2 gnt ehp  5 1 ⁄8 6 ”     (16 m     m x6 m) x6 naleb arkctes Handles: Important! If mounting a handle: to avoid damage, ensure fastenings do not protrude beyond the back surface of the panel. 2 Double models only: Important! Break off the tab at the top of the Lower Panel Bracket 3 7 SUC A

SUC A 8 5 6 2 a R n ec d  o a n  c n u e s c t t o in m g     t t o h e e     k w ic ir k  e ( s d   o a u n b d l   e � m tt o i d n el g s     t o h nl e y   ) panels 1 2 1 Important! Ensure the rubber seal between the drawer and panels is kept in place 2 1 5 6 ⁄8   ” (1 m 6     x m 5 m)  x 5

9 SUAC