La lecture à portée de main
Découvre YouScribe en t'inscrivant gratuitement
Je m'inscrisDécouvre YouScribe en t'inscrivant gratuitement
Je m'inscrisDescription
Sujets
Informations
Publié par | rheinisch-westfalischen_technischen_hochschule_-rwth-_aachen |
Publié le | 01 janvier 2005 |
Nombre de lectures | 22 |
Langue | Deutsch |
Poids de l'ouvrage | 10 Mo |
Extrait
Development and Evaluation
of a Test System
for the Quality Assurance
during the Mass Production
of Silicon Microstrip Detector Modules
for the CMS Experiment
Von der Fakultät für Mathematik, Informatik und Naturwissenschaften
der Rheinisch Westfälischen Technischen Hochschule Aachen
zur Erlangung des akademischen Grades eines
Doktors der Naturwissenschaften
genehmigte Dissertation
vorgelegt von
Torsten Franke
aus Rudolstadt
Berichter: Universitätsprofessor Dr. rer. nat Günter Flügge
Univ Dr. rer. nat. Joachim Mnich
Tag der mündlichen Prüfung: 04. Juli 2005
Diese Dissertation ist auf den Internetseiten der Hochschulbibliothek
online verfügbar.IIZusammenfassung
Der CMS Detektor (Compact Moun Solenoid) ist einer von vier Großdetektoren, die
im Rahmen des LHC Projektes (Large Hadron Collider) am Europäischen Zentrum
für Elementarteilchen Physik (CERN) errichtet werden. Der innere Spurdetektor von
CMS basiert vollständig auf Silizium Streifen Sensoren. Mit einer sensitiven Fläche
2von insgesamt 198 m wird er bei seiner Fertigstellung der weltweit größte, je gebaute
Spurdetektor seine Art sein. Für seinen Zusammenbau werden etwa 16.000 sogenan
nte Module benötigt, die jeweils aus den Silizium Streifen Sensoren, der Ausleseelek
tronik und einer Tragestruktur bestehen. Die Modulproduktion wird in einer Koop
eration von zahlreichen Instituten und Unternehmen bewerkstelligt. Für die Gewähr-
leistung eines zuverlässigen Betriebs der Module unter extremen Strahlenbelastungen
sind umfassende Tests aller Komponenten notwendig.
Ein wichtiger Beitrag zur Qualitätssicherung der Module wird durch die Bereitstel
lung eines Testsystems aus Aachen geleistet, das neben umfassenden Tests der Auslese
Elektronik auch Auskunft über möglich Fehler der Sensoren geben kann. Dieses Test
system wird im Rahmen der Modul Produktion in mehr als 20 beteiligten Instituten in
Europa und den USA eingesetzt.
Die automatisierte Überprüfung der Module erfordert eine spezielle Auslese und
Analysesoftware. Diese Software sowie alle Komponenten des Testsystems und deren
Funktionsweisen werden in der vorliegenden Arbeit beschrieben.
Ein Fehlerfindungalgorithmus wurde implementiert, der die genommenen Daten
auf charakteristische Signaturen verschiedener Typen von Modul Fehlern untersucht.
Eine zuverlässige Identifizierung fehlerhafter Streifen eines Moduls ist wichtig im Hin
blick auf entsprechende Reparaturmaßnahmen und die Beurteilung der Eignung eines
Moduls für die Verwendung im Spurdetektor.
Es wird ausführlich erklärt, wie die Tests bestimmt wurden, die am besten zur
Identifizierung eines Modulfehlers geeignet sind und wie der Fehlerfindungsalgorith
mus optimiert wurde, um dessen Zuverlässigkeit, unabhängig vom verwendeten Test
Setup, zu verbessern. Anhand der Daten von über 500 Modulen mit bekannten Fehlern
wurde die Eignung der gewählten Methoden überprüft.
Dabei wurden alle Fehler gefunden und in über 90 % der Fälle korrekt identi
fiziert. Gleichzeitig wurden weniger als 0,02 % der unbeschädigten Kanäle als fehler-
haft markiert. Die Beurteilung der Eignung eines Moduls erwies sich als nahezu unab
hängig vom speziellen Test Setup und ergab in ca. 96 % der Fälle das gleiche Resultat
für Module, die mehrfach getestet wurden.
Insgesamt wurden 0,3 % defekte Streifen gefunden und ca. 98 % der Module als
geeignet zur Verwendung im CMS Detektor klassifiziert.
IIIIVAbstract
The Compact Muon Solenoid (CMS) is one of four large scale experiments that is go
ing to be installed at the Large Hadron Collider (LHC) at the European Laboratory for
Particle Physics (CERN). For CMS an inner tracking system entirely equipped with
2silicon microstrip detectors was chosen. With an active area of about 198 m it will be
the largest tracking device of the world that was ever constructed using silicon sensors.
The basic components in the construction of the tracking system are approximately
16,000 so called modules, which are pre assembled units consisting of the sensors,
the readout electronics and a support structure. The module production is carried out
by a cooperation of number of institutes and industrial companies. To ensure the oper-
ation of the modules within the harsh radiation environment extensive tests have to be
performed on all components.
An important contribution to the quality assurance of the modules is made by a test
system of which all components were developed in Aachen. In addition to thorough
tests of the readout electronics and it enables the detection of many faults of the silicon
sensor it is connected to. It is used in more than 20 different institutes in Europe and
the USA which participate in the module production.
The application of the test system for automated tests of modules requires a ded
icated readout and analysis software. The software and all components of the test
system will be explained in detail in this thesis.
Different types of faults on a module show a significant behaviour in particular
tests. A dedicated fault finding algorithm searches for these signatures. A safe identi
fication of faulty channels and a reliable information on the respective type of fault is
important. It facilitates the reparation and enables the assessment of the appropriate
ness of a module for the insertion into the tracker. It will be explained which approach
was used to find the most appropriate tests for that purpose and how the fault find
ing algorithm was optimized to give reliable results independent of the specific test
setup. Finally, the algorithm is used for the qualification of more than 500 repeatedly
measured modules with known failures to verify its suitability.
All faulty channels are found and more than 90 % of the faults are correctly identi
fied. At the same time less than 0.02 % of good channels are wrongly flagged as faulty.
The assessment of the module quality is nearly independent of the particular setup and
can be reproduced in about 96 % of the cases of repeatedly measured modules.
In total, less than 0.3 % of the channels are faulty and about 98 % of all modules
are suited for the construction of the tracker.
VVIContents
1 Introduction 1
1.1 The Large Hadron Collider . . . . . . . . . . . . . . . . . . . . . . . 2
1.2 The CMS Experiment . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3 The Silicon Strip Tracker . . . . . . . . . . . . . . . . . . . . . . . . 5
2 The CMS Silicon Tracker Modules 9
2.1 Energy Loss due to Ionization . . . . . . . . . . . . . . . . . . . . . 9
2.2 The Function Principle of a Silicon Strip Detector . . . . . . . . . . . 12
2.3 Design Goals and Operation Principles . . . . . . . . . . . . . . . . . 14
2.3.1 Depletion Voltage . . . . . . . . . . . . . . . . . . . . . . . . 15
2.3.2 Leakage Current . . . . . . . . . . . . . . . . . . . . . . . . 16
2.3.3 Trapping of Signal Charge . . . . . . . . . . . . . . . . . . . 17
2.3.4 Detector Capacitances . . . . . . . . . . . . . . . . . . . . . 17
2.3.5 Annealing and Reverse Annealing . . . . . . . . . . . . . . . 18
2.4 Layout of the CMS Silicon Microstrip Sensors . . . . . . . . . . . . . 19
2.5 The CMS Silicon Strip Tracker Modules . . . . . . . . . . . . . . . . 20
2.5.1 Design of the Module Mechanics . . . . . . . . . . . . . . . 20
2.5.2 The Front End Hybrid . . . . . . . . . . . . . . . . . . . . . 21
2.5.3 The APV Chip . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.5.4 The MUX Chip . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.5.5 The TPLL Chip . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.5.6 The DCU Chip . . . . . . . . . . . . . . . . . . . . . . . . . 28
2.6 Possible Module Faults . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.6.1 Problems in the Sensor Production . . . . . . . . . . . . . . . 29
2.6.2 ASIC and Hybrid Problems . . . . . . . . . . . . . . . . . . 32
2.6.3 Module Production and Handling Problems . . . . . . . . . . 33
3 The APV Readout Controller System 35
3.1 System Overwiew . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.2 The ARC Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.2.1 Trigger Generation . . . . . . . . . . . . . . . . . . . . . . . 38
3.2.2 Data Acquisition . . . . . . . . . . . . . . . . . . . . . . . . 40
3.2.3 Slow Control . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3.3 The Front End Adapter . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.3.1 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
iii CONTENTS
3.3.2 Versions of the Front End Adapter . . . . . . . . . . . . . . . 43
3.4 The LED Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.4.1 The LED Controller Board . . . . . . . . . . . . . . . . . . . 45
3.4.2 The Choice of the LEDs . . . . . . . . . . . . . . . . . . . . 46
3.4.3 The Transmission of Light to the Sensors . . . . . . . . . . . 47
3.5 The High Voltage Controller . . . . . . . . . . . . . . . . . . . . . . 48
3.6 The Single Module Test Box . . . . . . . . . . . . . . . . . . . . . . 50
3.7 Cold Box Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
3.7.1 The Cold Box Design .