//img.uscri.be/pth/958d4feae1cf1d4c0e0b9ac46f7f274786203298
La lecture en ligne est gratuite
Le téléchargement nécessite un accès à la bibliothèque YouScribe
Tout savoir sur nos offres
Télécharger Lire

Notice Sécurité Ademco VISTA-128FB

De
24 pages

Notice utilisateur, mode d'emploi du modèle 'VISTA-128FB' de marque 'Ademco'

Publié par :
Ajouté le : 28 mai 2011
Lecture(s) : 93
Signaler un abus



ADEMCO VISTA-12E
Security Systems


Programming Guide









































K10022-5PR 10/05 Rev. A
TO START PROGRAM MODE, use method A or B (must use alpha keypad connected to keypad terminals):
∗A. POWER UP, then press both [ ] and [#] at same time within 50 seconds of powering up.
∗ (if 98 was used to exit program mode, this is the only method that can be used to start program mode again)
B. Initially, key: Installer Code (4 + 1 + 1 + 2) plus 8 + 0 + 0.


Data Field Programming Procedures
Task Procedure
∗Go to a Data Field Press [ ] + [Field Number], followed by the required entry.
Entering Data When the desired field number appears, simply make the required entry. When the last entry for a field
is entered, the keypad beeps three times and automatically displays the next data field in sequence.
If the number of digits that you need to enter in a data field is less than the maximum digits available
∗(for example, the phone number fields *41, *42), enter the desired data, then press [ ] to end the entry.
Review a Data Field Press [#] + [Field Number].
Data will be displayed for that field number. No changes will be accepted in this mode.
∗ ∗ ∗ ∗ ∗ ∗Deleting an Entry Press [ ] + [Field Number] + [ ]. (Applies only to fields 40– 43, 45, 94, and pager programming
fields)

Menu Mode Programming (∗56, ∗57, ∗58, ∗79, ∗80, ∗81, ∗82, ∗83)
✱Press [ ] + [Interactive Mode No.] (for example, ∗56). The alpha keypad displays the first of a series of prompts.
Interactive Mode Used to Program
✱56 Zone Programming Zone characteristics, report codes, alpha descriptors, and serial numbers for 5800 RF
transmitters.
✱57 Function Key Programming Unlabeled keypad keys (known as ABCD keys) for special functions
✱58 Zone Programming Same options as *56 mode, but with fewer prompts. Intended for those familiar with
(Expert mode) this type of programming, otherwise *56 mode is recommended.
✱79 Output Device Mapping Assign module addresses and map individual relays/powerline carrier devices
✱80 Output Programming 4229 or 4204 Relay modules, 6164 output relay, Powerline Carrier devices, or on-
board triggers
✱81 Zone List Programming Zone Lists for relay/powerline carrier activation, chime zones, pager zones, etc.
✱82 Alpha Programming Zone alpha descriptors
✱83 Configurable Zone type Prog Attributes for configurable zone types

INITIALIZE DOWNLOAD and RESET DEFAULTS (complete Default Tables are listed on page 20)
✱96 Initializes download ID and subscriber account number.
✱97 Sets all data fields to original factory default values as follows:
The VISTA-12E has two unique sets (tables) of default entries.
Press ∗97 while in Program Mode, then press 1 or 2 to load the desired set of factory defaults (see Default Tables
listed on page 20). This resets all data fields to the respective default table values.

User Code Defaults: To reset only the user codes to default values, press ∗97, then press 3.

TO EXIT PROGRAMMING MODE:
✱ ✱98 Exits programming mode and prevents re-entry by: Installer Code + 8 + 0 + 0. If 98 is used to exit programming
mode, system must be powered down, and method 1 above used to enter the programming mode.
✱99 Exits programming mode and allows re-entry by: Installer Code + 8 + 0 + 0 or method A above.

Special Messages
OC = OPEN CIRCUIT (no communication between keypad and Control).
EE or ENTRY ERROR = ERROR (invalid field number entered; re-enter valid field number).
After powering up, AC, dI (disabled) or Busy Standby and NOT READY will be displayed after approximately 4 seconds.
This will revert to a “Ready” message in approximately 1 minute, which allows PIRS, etc. to stabilize. You can bypass this
delay by pressing [#] + [0].
If E4 or E8 appears, more zones than the expansion units can handle have been programmed. Correct the programming
and then completely de-power and re-power the control to clear this indication and remove the disable indication.

– 2 – PROGRAMMING FORM
Entry of a number other than one specified will give unpredictable results. Default values are shown in brackets, with unique table 1 and table 2
values indicated where applicable (DT1 = default table 1; DT2 = default table 2); see page 20 for a complete list of factory default tables 1 and 2.
∗ ∗38 Confirm. Arming Ding (continued) 20 Installer Code [4112] | | |
( Enter 0-15 from table. 0–9 = 4 digit installer code
Entry Ding at Siren Trigger 2 Output
0 none none NOTE: ∗21 Quick Arm Enable [1,1,1]
1 none250mS If using trigger 2
0 = no quick arm; 1 = allow quick arm Part. 1 Part. 2 Com
2 none 1 second output for arming
3 none 4 seconds ding, do not assign ∗22 RF Options [0,0]
4 250mS none any other functions
Entry 1 - 0 = no RF Jam detection; 1 = detect RF Jam Jam Supv 5 S 250mS to trigger 2.
Entry 2– supervision interval; 0 = 12 hour; 1 = 2 hour; 2 = 20 min if
6 250mS 1 second
disarmed/2 hrs if armed; 3 = 12 hrs for burg zones/3 hrs for fire zones
7 S 4 seconds
∗∗23 Quick (Forced) Bypass [0,0,0] 8 1 second none ∗∗
9 1 second 250mS
0 = no quick bypass Part. 1 Part. 2 Com
#+10 1 second 1 second
1 = allow quick bypass (code + [6] + [#])
#+11 1 second 4 seconds
#+12 4 seconds none ∗24 RF House ID Code [00,00,00] | | |
#+13 4 seconds 250mS
00 = disable all wireless keypad usage Part. 1 Part. 2 Com #+14 4 seconds 1 second
01–31 = house ID for use with 5827, 5827BD keypad or
#+15 4 seconds 4 seconds
5804BD/5804BDV keyfob
∗∗∗∗25 Arming Prevention Override [6,0] ∗∗∗∗39 Power-Up In Previous State [1]
If no override is selected, system will not arm when there is either a 0 = always power-up disarmed; 1 = power-up in previous state
supervision failure, system low battery, AC loss, or tamper. For dialer fields ∗40 – ∗42, enter the number of digits shown. Do not fill
Entry 1 0 = no arming prevention override unused spaces. Enter 0–9; #+11 for '∗'; #+12 for '#'; #+13 for a 2-second
1 = allow system to arm with an RF supervision failure pause. If fewer than the maximum digits entered, exit the field by pressing [✶].
2 = allow system to be armed with an AC Mains Loss The next data field is displayed.
4 = allow system to be armed with a system low battery
E.g., To select arm with “supervision failure” and “system low ∗40 PABX Access Code | | | | |
battery”, enter 5 (1 + 4);
Enter up to 6 digits. If fewer than 6 digits are entered, exit by pressing Entry 2 0 = no tamper override (see field *175 for more tamper options)
[✶]. To clear entries from field, press ∗40∗ 1 = allow system to be armed with a tamper fault
2 = allow system to be armed with a tamper fault once ∗41 Primary Phone No.
NOTE: If tamper option 1 or 2 is selected, field *175 digit 2 must be “0.”
| | | | | | | | | | | | | |
∗26 Chime By Zone [0]
0 = no; 1 = yes (select chime zones on zone list 3, see *81 Menu mode) | | | | | | | | | | | | | |
∗27 Powerline Carrier (X–10) House Code [0] ∗42 Second Phone No.
0 = A; 1 = B, 2 = C, 3 = D, 4 = E, 5 = F, 6 = G, 7 = H, 8 = I, 9 = J,
| | | | | | | | | | | | | | #10 = K, #11 = L, #12 = M, #13 = N, #14 = O, #15 = P

∗29 ECP Contact ID Output for ACM [0] | | | | | | | | | | | | | |
0 = no; 1 = use Contact ID output on ECP terms. (e.g. TCP-IP ethernet)

Enter up to 30 digits for each phone number. To clear entries, press ∗31 Single Alarm Sounding/Zone [0] ∗41∗ or ∗42∗ respectively.
0 = no; 1 = yes, only one alarm sounding per armed period per zone For fields *43, *44 , *45, *46, *51 and *52, enter 4, 6 (Robofon 8), or 10
digits, depending on selection in *48 Report Format. Enter 0–9; #+11 for B; ∗32 Fire Alarm Sounder (Bell) Timeout [0]
#+12 for C; #+13 for D; #+14 for E; #+15 for F. To clear entries from field,
0 = sounder stops at timeout; 1 = no sounder timeout press *43*, *44*, *45*, *46*, *51* or*52* respectively. Examples: For Acct.
1234, enter 1 | 2 | 3 | 4 ; For Acct. B234, enter #+11| 2 | 3 | 4 ∗33 Siren (Burglary) Timeout [3]

0=none; 1 =1 min; 2 =2 min; 3 =3 min; 4 =4 min; 5 =8 min; 6 =16 min
∗43 Primary Subscriber ID # (Part. 1)
∗34 Exit Delay [97,97,97] | | | | | | | | |
00 to 96 = 00 to 96 seconds respectively Part 1 Part 2 Com
97 = 120 seconds ∗44 Secondary Subscriber ID # (Part. 1)
∗35 Entry Delay 1 (zone type 01) [30,30,30] | | | | | | | | |
00 to 96 = 00 to 96 seconds respectively Part 1 Part 2 Com
∗45 Primary Subscriber ID # (Part. 2) 97 will = 120 seconds; 98 will = 180 seconds; 99 will = 240 seconds
| | | | | | | | | ∗36 Entry Delay 2 (zone type 02) [30,30,30]
See *35 for entries. Part 1 Part 2 Com ∗46 Secondary Subscriber ID # (Part. 2)
∗37 Audible Exit Warning [0,0,0] | | | | | | | | |
0 = no; 1 = yes Part 1 Part 2 Com
∗47 Phone System Select/Dialer Attempts
∗∗∗∗38 Confirm. Arming Ding [00,00,00] | | |
Phone System Select: [3,8] Select Attempts
Entry 1 for each partition selects Part 1 Part 2 Com If Cent. Sta. IS NOT on a satellite link: 0=Pulse Dial; 1=Tone Dial;
whether arming from wired keypads causes siren ding: if Cent. Sta. IS on a satellite link: 2 = Pulse Dial ; 3 = Tone Dial
0 = no; 1 = yes, ding and siren for time selected in entry 2 Dialer Attempts: 1 – 10 (for 10, enter #+10)
Entry 2 for each partition selects whether arming from keyswitch and/or
remote RF devices causes siren ding and/or activates trigger 2 output;
also selects ding/trigger activation duration (arm = 2 dings of selected
duration with 1 second off between; disarm = 1 ding of selected
duration).

(field *38 continued at top of next column)
– 3 – ∗66 Arm Away/Stay Rpt Code ∗48 Report Format [7,7]
0 = 3+1,4+1, ADEMCO L/S STANDARD prim. second [1,0;1,0;1,0]
1 = 3+1,4+1, RADIONICS STANDARD NOTES: To enable
AWAY STAY AWAY STAY AWAY STAY 2 = 4+2, ADEMCO L/S STANDARD audio “beeps” format
Part. 1 Part. 2 Common 3 = 4+2, RADIONICS STANDARD (Follow-Me feature),
5 = CID using 10-digit subs account (ID) no. refer to the System
∗∗∗∗67 RF Trans. Low Bat Report Code [10] | 6 = 4+2, ADEMCO EXPRESS Communication and

7 = CID using 4-digit subs account (ID) no. Operation section in
8 = 3+1,4+1, ADEMCO L/S EXPANDED the Instr’s. Also see ∗68 Cancel Report Code [00] |
9 = 3+1,4+1, RADIONICS EXPANDED *53 and *188 for
1 = dynamically as the fault clears; 2 = only after a disarm #+10 = ROBOFON 8 (6-digit subs acc’nt no.) notes on certain
#+11 = ROBOFON Contact ID Contact ID codes. ∗69 Alarm Restores [1]
∗49 Split/Dual Reporting [0] Send restore code (if fault cleared):
0 = at siren timeout (if restored) or at disarm (whether restored or not) 0 = Disable (standard/backup reporting only)
Primary Phone No. Second Phone No. ∗∗∗∗70 Alarm Restore Rpt Code [1]
1 = Alarms, Restore, Cancel Others

2 = All except Open/Close, Test Open/Close, Test
∗71 Trouble Restore Rpt Code [10] | 3 = Alarms, Restore, Cancel All

4 = All except Open/Close, Test All
5 = All All ∗72 Bypass Rest. Rpt Code [10] |

∗50 Dialer Delay (Burg) [0] ∗73 AC Restore Rpt Code [10] |
0 = none; 1 = 15 seconds; 2 = 30 seconds; 3 = 45 seconds
∗∗∗∗74 Low Bat Restore Rpt Code [10] | ∗∗∗∗51 Primary Subscriber ID # (Common Part.)

| | | | | | | | | ∗75 RF Low Battery Restore Rpt Code [10] |

∗52 Secondary Subscriber ID # (Common Part.) ∗76 Test Restore Rpt Code [10] |
| | | | | | | | |
∗77 Summer Time Start\End Month [00] | Fields *51 and *52 see box above ∗43 for entries.
0 = Disabled; 1-12 = month (1 = January, 2 = February, etc) ∗53 SESCOA/Radionics and CID Enbl [0,0] #+10 = October; #+11 = November; #+12 = December
SESCOA/Radionics Select: Ses/Rad CID ∗78 Summer Time Start\End Weekend [00] |
0 = Radionics (0-9, B-F); 1 = SESCOA (0-9)
CID Enable: 0 = disabled; 1 = first; 2 = second; 3 = third
0 = disable both Time/Date Inaccurate and Successful 4 = fourth; 5 = last; 6 = next to last; 7 = third to last
Download/Access reports
∗84 Auto Stay Arm [0] 1 = enable Time/Date Inaccurate report (code 626)
2 = enable Successful Download/Access report (code 412) 0 = none; 1 = partition 1; 2 = partition 2; 4 = partition 3
3 = enable both Time/Date Inaccurate and Successful Add the values for multiple partitions.
Download/Access reports
∗∗85 Linked Zone Verification Timer/ [0,0] NOTE: Time/Date Inaccurate report (CID 626) and Successful ∗∗
Download/Access report (CID 412) are sent only if Contact ID format
Up and About Timer Linked Up/about is selected as reporting format in field *48.
Linked Zone: Assign linked zones on zone list 4, with *81 Menu mode.
∗54 Dynamic Signaling Delay [0] 0 = 15 seconds 4 = 90 seconds 8 = 4 min #+12 = 8 min
1 = 30 seconds 5 = 2 minutes 9 = 5 min #+13 = 10 min Delay selectable from 0 to 225 secs in 15-sec increments.
2 = 45 seconds 6 = 2-1/2 min #+10 = 6 min #+14 = 12 min 0 = no delay (both signals sent); 1 = 15 secs; 2 = 30 secs, etc.
3 = 60 seconds 7 = 3 min #+11 = 7 min #+15 = 15 min
∗55 Dynamic Signaling Priority [0] Up and About Timer: 1-15 hours (also need to program up and about
schedule for time window that up and about feature is active; value set
0 = Primary Dialer first; 1 = ECP Contact ID first (e.g., TCP-IP ethernet)
in this field is time within the schedule that activity must occur)
TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES:
∗86 Cancel Verify Keypad Display [0] For 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–9,
#+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F. 0 = no “alarm canceled” display
A 0 (not #+10) in the first box will disable a report. A 0 (not #+10) in the 1 = display “Alarm Canceled” when system is disarmed after an alarm
second box will result in automatic advance to the next field. has occurred. (To clear the “ALARM CANCELED” display, the
For Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) user must enter the security code + OFF again.)
for 1–9, 0, or B–F, as described above.
A 0 (not #+10) in the second box will eliminate the expanded message for ∗87 Misc. Fault Delay Time [0]
that report. A 0 (not #+10) in both boxes will disable the report.
(for Configurable Zone Type zones - alarm/trouble processing option)
For ADEMCO Contact ID® Reporting: Enter any digit (other than 0) in the first
0 = 15 seconds 4 = 90 seconds 8 = 4 min #+12 = 8 min
box, to enable zone to report (entries in the second boxes are ignored).
1 = 30 seconds 5 = 2 minutes 9 = 5 min #+13 = 10 min
A 0 (not #+10) in the first box disables the report.
2 = 45 seconds 6 = 2-1/2 min #+10 = 6 min #+14 = 12 min
3 = 60 seconds 7 = 3 min #+11 = 7 min #+15 = 15 min ∗59 Exit Error Report Code [0]
∗88 Exit Options [1]
∗60 Trouble Report Code [10] |
0 = all intrusion zones must be intact before arming(must be 0 if

system uses zone type 82 - Blockschloss)
∗61 Bypass Report Code [10] | 1 = All intrusion zones except in exit path (zone list 12) must be

intact before arming. Exit path zones cause alarm if not restored
∗∗∗∗62 AC Loss Report Code [10] | at end of exit time
2 = All intrusion zones except in exit path (zone list 12) must be
intact before arming. Exit path zones are bypassed if not restored ∗63 Low Bat Report Code [10] |
at end of exit time
3 = Final contact set: All intrusion zones except in exit path ∗64 Test Report Code [10] |
(zone list 12) must be intact before arming. Once armed, exit
First test report sent 12 hours after exiting program mode. delay remains on indefinitely until the last zone, as defined in
Use Scheduling mode to change periodic test report schedule. zone list 8, is restored; then there is 5-second exit delay before
arming state is active
∗∗∗∗65 Open Report Code [0,0,0]

Part. 1 Part. 2 Com
– 4 – ∗89 Event Log Full Report Code [00] | ∗166 Pager Delay Option For Alarms [0]
See box above ∗59 for entries. 0 = none, 1 = 1 minute, 2 = 2 minutes, 3 = 3 minutes
This delay is for ALL pagers in the system. The delay does not reset ∗90 Event Log Enables [15] for new alarms occurring while an existing pager delay is in progress.
0 = None; 1 = Alarm/Alarm Restore; 2 = Trouble/Trouble Restore; ∗∗∗∗173 RF Reporting Options [1] 4 = Bypass/Bypass Restore; 8 = Open/Close. Ex: For “Alarm/Restore”
and “Open/Close”, enter 9 (1 + 8); To select all, enter #15. 0 = none; 1 = RF Tamper reports during disarm
NOTE: System messages logged when any non-zero entry is made. 2 = RF keyfobs send low battery
3 = RF Tamper reports during disarm and RF keyfobs send low battery ∗91 Miscellaneous Options [0.1]
∗175 Tamper Options [0,0] Entry 1: 0 = None; 4 = Audio Alarm Verification (AAV); 1 2
8 = Exit Delay Restart; #+12 = AAV (4) and Exit Delay (see field *25 for tamper override options when arming) 1 2
Restart (8) Entry 1: 0 = standard tamper protection
Entry 2: 0 = allow keypad output activation commands 1 = detect tamper from bypassed zones
(user code + # + 7 and user code + # + 8) 2 = detect tamper when in Test mode
1 = do not allow keypad output activation commands 3 = detect tamper when in Test mode from bypassed zones
Entry 2: 0 = all users can clear a tamper (must be “0” if field *25 digit ∗92 Telecom Monitor Enable [0,0]
2 set to 1 or 2)
Entry 1: 0 = disabled 1 2 1 = only the installer can clear a tamper
1-15 = enabled, after 1 15 min. line outage
∗176 Siren Options [0,0] (#+10 = 10 min; #+11 = 11 min; #+12 = 12 min;
#+13 = 13 min; #+14 = 14 min; #+15 = 15 min) Entry 1: 0 = external siren; 1 = self-activated external siren 1 2
Entry 2: 0 = keypad display when line is faulted Entry 2: 0 = disable (2nd digit ignored if 1st digit not set to ext. siren)
1 = keypad display plus keypad trouble sound 1 = enable 30 second ext. siren and dialer delay during entry
2 = Same as “1”, plus programmed output device STARTS. If delay period when armed AWAY (if entry delay is active
any partition is armed, external sounder also activates. and an instant zone is faulted, the siren is delayed 30
NOTE: Output Device must either be programmed to be STOPPED seconds, and the report is delayed 30 secs. unless field
in field ∗80 or STOPPED by Code + # + 8 + output number. *50 is set for a greater delay)
2 = external siren and dialer delayed 15-seconds when ∗93 No. of Reports in Armed Period [0]
armed in STAY mode
Per Zone (Intermittent Sensor)
∗177 Device Duration 1, 2 [0,0]
0 = Unlimited Reports; 1 - 6 = 1 - 6 report pairs
(used in *80 Output Definitions menu -Device Actions 5/6) 1 2
∗∗∗∗94 Download Phone No. Duration 1 – Device Action 5 Timer
0 = 15 seconds 4 = 90 secs 8 = 4 min #+12 = 8 min | | | | | | | | | | | | | |
1 = 30 seconds 5 = 2 min 9 = 5 min #+13 = 10 min

2 = 45 seconds 6 = 2-1/2 min #+10 = 6 min #+14 = 12 min
| | | | | | | | | | | | | | 3 = 60 seconds 7 = 3 min #+11 = 7 min #+15 = 15 min
Duration 2 – Device Action 6 Timer (Strobe Timer) Enter up to 30 digits, 0–9; #+11 for '∗'; #+12 for '#'; #+13 for a 2-
1 – 7 = 1 to 7 days second pause. Do not fill unused spaces. If fewer than 30 digits, exit
field by pressing ∗. To clear entries from field, press ∗94∗.
∗178 RF Supervision and RF Jam Option [0]
∗95 Ring Count For Downloading [15] 0 = Basic RF supervision and RF jam detection
1 = Report RF supervision failure as tamper alarm when armed 0 = Disable Monitoring Station Initiated Download;
2 = Report RF Jam as tamper alarm when armed 1–14 = number of rings (1–9, # +10 =10, # +11 =11, # +12 =12,
3 = Report RF Jam & RF supervision failure as tamper alarm when armed # +13 =13, # +14 =14);
15 = Answering machine/fax defeat (# +15 =15). ∗180 Zone Bypass Limit [0]
∗160 Pager 1 Phone No. 0 = unlimited zone bypasses in each partition

1-7 = number of zone bypasses allowed in each partition
| | | | | | | | | | | | | | | | | | | (each partition individually uses this entry)
8 = zone bypass disabled (no zones can be bypassed) Enter up to 20 digits, 0–9; #+11 for '∗'; #+12 for '#'; #+13 for a 2-
second pause. Do not fill unused spaces. If fewer than 20 digits, exit ∗∗∗∗181 AC and Clock Display Options [5]
field by pressing ∗. To clear entries from field, press ∗160∗.
Use the following table to select the desired options for real-time
∗161 Pager 1 Characters clock synchronization (50Hz, 60Hz, Crystal), AC Loss display
(independent of AC Loss report enabled in *62), and clock display
| | | | | | | | | | | | | | |
(time displayed on bottom line of alpha keypads).
“X10” indicates the AC frequency used for powerline carrier devices. Enter the optional prefix characters, up to 16 digits.
0–9; #+11 = '∗'; #+12 = '#'; #+13 = 2-second pause. Entry AC Freq. Crystal for AC Loss disp Clock disp
0 60Hz clock backup no no
∗162 Pager 1 Reporting Options 1 50Hzclockback
For each partition, select from: [0,0,0] Part. 1 Part. 2 Part 3 2 60Hz clock no no
0 = no reports sent; 1 = Open/close all users; 4 = All alarms and troubles 3 50Hzclock
5 = All alarms / troubles, and open/closes for all users 4 60Hz clock backup yes no
12 = Alarms / troubles for zones entered in zone list 9
5 50Hzclockbackye
13 = Alarms / troubles for zones entered in zone list 9, and
6 60Hz clock yes no opens/closes for all users
7 50Hzclockye
∗163 Pager 2 Phone No. (See field *160 for entries.) 8 60Hz clock backup no yes

9 50Hzclockbackye | | | | | | | | | | | | | | | | | | |
#+10 60Hz clock no yes
#+11 50Hzockye
#+12 60Hz clock backup yes yes ∗164 Pager 2 Characters (See field *161 for entries.)
#+13 50Hzock backyes yes
| | | | | | | | | | | | | | | #+14 60Hz clock yes yes
#+15 50Hzockyeye
∗165 Pager 2 Reporting Options
∗182 Summer Time Switchover Day [0]
See field *162 for entries. [0,0,0] Part. 1 Part. 2 Part 3
0 = switch on Sunday morning; 1= switch on Saturday morning Use zone list 10 if using options 12 or 13.
2 = switch on Friday morning
– 5 – KEYPAD OPTIONS ∗183 Date/Time Format [3]
NOTES: 1. Keypad 1 (addr 16) options are factory set and cannot be changed.
0 = 12-hour time/MMDDYY date 2 = 24-hour time/MMDDYY date 2. Each keypad must be assigned a unique address. Keypads
1 = 12-hour time/DDMMYY date 3 = 24-hour time/DDMMYY date programmed with the same address will give unpredictable results.
∗185 Downloader Suppression Options [0] ∗190 Keypad 2 Device Address 17 [0] [0]
0 = no suppression; 1 = suppress user code viewing Partition: 0 = keypad disabled; 1-3 = part. no. Part. Sound
2 = suppress commands and program download when armed Sound: 0 = no suppression
3 = suppress user code viewing, commands, and program download 1 = suppress arm/disarm and E/E beeps
when armed 2 = suppress chime beeps only
3 = suppress arm/disarm, E/E, & chime beeps ∗186 Display Options [0,0] Fields*191-*196 see field ∗190 for entries. Part. Sound
Entry 1: Latch the first alarm in the display: 0 = disable; 1 = enable
∗191 Keypad 3 Device Address 18 [0] [0] Entry 2: Turn off the display (except for AC loss) except during exit
delay. Turns off when exit delay expires, or 30 seconds after
disarm; 0 = disable; 1 = enable ∗∗∗∗192 Keypad 4 Device Address 19 [0] [0]
∗187 Sounder Mimic on Trigger 1 [0]
∗193 Keypad 5 Device Address 20 [0] [0]
0 = no sound output on trigger 1
1 = mimic keypad 1, address 16 5 = mimic keypad 5, address 20 ∗194 Keypad 6 Device Address 21 [0] [0]
2 = mimic keypad 2, address 17 6 = mimic keypad 6, address 21

3 = mimic keypad 3, address 18 7 = mimic keypad 7, address 22
∗195 Keypad 7 Device Address 22 [0] [0] 4 = mimic keypad 4, address 19 8 = mimic keypad 8, address 23

NOTE: If used, do not assign any other functions to trigger 1.
∗∗∗∗196 Keypad 8 Device Address 23 [0] [0]
∗∗∗∗188 Keypad Sabotage Options [0,0]

Entry 1: Keypad Lockout: 0 = disable; 1 = enable 15 minute lockout ∗197 Exit Time Display Interval [0]
NOTE: 461 Wrong Code Entry is sent only if Contact ID
0 = no display; 1-5 = seconds between display refresh format is selected as reporting format in field *48 (if
Contact ID format is not being used, this event is not ∗198 Display Partition Number [0]
reported)
0 = no; 1 = yes (partition number displays on alpha keypads) Entry 2: Keypad Supervision and Tamper Fault Detection:
0 = no, 1 = yes
∗199 ECP Device Fail Display [0] NOTE: All lockout, supervision, and tamper events are recorded in
the event log regardless of the settings in entries 1 and 2. 0 = 3-digit display (“1” + device address); for 6148, 6164

1 = 2-digit fixed-display as “91;” for 6128 series keypads
∗189 AUI Device 1 and 2 Enable [0,0]
(for Touch Screen Style Keypads) AUI 1AU2
System supports up to two touch screen style keypads (e.g., Symphony
Advanced User Interface, and 6270 Touch Screen Keypad).

AUI Compatibility Note: To ensure proper AUI device operation, use
AUI devices with the following rev levels: 6270 series use version
1.0.9 or higher; 8132/8142 (Symphony) series use version 1.1.175 or
higher.

Touch Screen (AUI) device 1: Must set AUI device address to 1
Tcreen (AUI) device 2: Must set AUI device address to 2

Enter each AUI’s home partition.
0 = disabled
1 = partition 1; 2 = partition 2; 3 = common partition



– 6 – ✱56 ZONE PROGRAMMING WORKSHEET [default values shown in brackets]

Zone Zn Type Partition Report Basic Wired Type Response Time Location
1 [01] [1] [yes] [EOL] [1]
2 [04] [1] [yes] [EOL] [1]
3 [03] [1] [yes] [EOL] [1]
4 [03] [1] [yes] [EOL] [1]
5 [03] [1] [yes] [EOL] [1]
6 [03] [1] [yes] [EOL] [1]
Zone Zn Type Partition Report Input Type Loop Serial Number Location
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
[yes] 49 [1] [BR]
[yes] 50 [1] [BR]
[yes] 51 [1] [BR]
[yes] 52 [1] [BR]
[yes] 53 [1] [BR]
[yes] 54 [1] [BR]
[yes] 55 [1] [BR]
[yes] 56 [1] [BR]
57 [yes] [1] [BR]
[yes] 58 [1] [BR]
[yes] 59 [1] [BR]
[yes] 60 [1] [BR]
[yes] 61 [1] [BR]
[yes] 62 [1] [BR]
[yes] 63 [1] [BR]
64 [1] [yes] [BR]
[yes] 91 [05] N/A N/A N/A N/A Addressable Device Report
92 N/AAN/A N/AN/A Duress Report
95 [00] N/A N/A N/A keypad [1] / [∗]
96 [00] N/A N/A N/A ke3] / [#]
99 [yes] [07]N/A N/A N/A keypad [∗] / [#]

NOTES:
Zone Type: see chart on next page Report:
yes = Contact ID reporting enabled for this zone; entered as 01 00 in appropriate data
Basic wired Type (zns 1-6): fields.
0 = EOL
1 = NC Response Time:
2 = NO 0 = 10msec
3 = zone doubling 1 = 400msec
4 = double-balanced 2 = 700msec
3 = 1.2 sec
Input Type: NOTE: If zone doubling is selected, the response time selected for the basic zone
2 = AW (zones 17-24) automatically applies to the associated doubled zone.
3 = RF (zones 9-24)
4 = UR (zones 9-24) Reserved Zones
5 = BR (zones 49-64) 91 = addressable device report enable/disable
7 = RM (zones 9-24) default zone type = [05].
NOTE: Zones 9-14 not available depending on whether zone 92 = Duress report enable/disable
doubling enabled on zones 1-6.

– 7 – ∗56 ZONE PROGRAMMING MENU MODE (press ✱56 while in Program mode)
0 = no SET TO CONFIRM?
1 = yes (prompt appears after entering the serial and loop numbers to confirm each transmitter)
0 = NO 1 = YES We recommend that you confirm the programming of every transmitter.

Enter the zone number being programmed: Enter Zn Num.
wired zones 01-6 and 10-14 for zone doubling; expansion zones 17-24; wireless zones 09-24; RF button
(00 = Quit) 10 zones 49-64
91 = addr. device report enable (Enter a report code for zone 91 to enable addressable device reporting.
92 = duress report enable (Enter a report code for zone 92 to enable duress reporting)
95, 96, 99 =emergency zones
00 to quit; [∗] to continue

Summary Screen
Zn ZT P RC In: L [∗] to continue; “IN: L” = input type and loop; “IN: AD” = wired expansion module address
10 00 1 10 RF: 1 “HW: RT” = basic wired zone configuration (EOL, NO, NC, zone doubling, double-balanced) and response
time

Enter the desired ;zone type from the list below. If 00 is entered, Delete Zone ? is displayed.
10 Zone Type 00 = Not used 08 = 24-Hr Aux 21 = Arm–AWAY*
01 = Entry/exit #1 09 = Fire 22 = Disarm* Perimeter 03
02 = Entry/exit #2 10 = Interior w/Delay 23 = No Alarm Resp
03 = Perimeter 12 = Monitor Zone 24 = Silent Burglary
04 = Interior Follower 14 = Gas 77 = Keyswitch
05 = Trouble Day/Alarm Night 15 = Medical 81 = AAV Monitor Zone
06 = 24-Hr Silent 16 = Fire w/Verify 82 = Blockschloss Keyswitch
07 = 24-Hr Audible 20 = Arm–STAY* 90-93 = Configurable
*5800 button-type transmitters only

Enter the desired partition for this zone
10 Partition 1-3 = partition
[∗] to continue 1

Enter the report code for this zone, which consists of 2 hexadecimal digits, each in turn consisting of 2
10 Report Code numerical digits. For example, for a report code of “10,” enter 01 and 00.
For Contact ID®, entering any non-zero entry as the first digit enables the report code for this zone. 1st 01 2nd 00 10
1-9, 10 for A, 11 for B, 12 for C, 13 for D, 14 for E, 15 for F
00 to disable; [∗] to continue

This prompt appears only for zone numbers 01-06.
02 HARDWIRE TYPE Enter the desired basic wired type:
EOL 0 0 = EOL; 1 = NC; 2 = NO; 3 = zone doubling (ZD); 4 = double-balanced (DB)
[∗] to continue

This prompt appears only for basic wired zones 01-06 (zone 02 is used as an example in display).
02 Response Time 0 = 10mSec; 1 = 400mSec; 2 = 700mSec; 3 = 1.2 seconds
[∗] to continue 1

This prompt is skipped for zones 1-6, and for zones 9-14 if zone-doubling enabled at “Hardwire Type” prompt.
10 INPUT TYPE All of the RF transmitters have one or more unique input loops (see list below). Each of the input loops
requires its own programming zone (e.g., a 5804's four inputs requires four zones). RF TRANS 3
2 = AW (Aux wired zone)
3 = RF (supervised RF transmitter; sends fault, restore, and low-battery signals, and sends periodic check-in
signals; transmitter must stay within receiver's range)
4 = UR (unsupervised RF transmitter; sends fault, restore, and low-battery signals, but periodic check-in
signals are not supervised; transmitter may be carried off-premises)
5 = BR (unsupervised button type RF transmitter; sends fault and low battery signals when activated, does
not send restore or check-in signals; transmitter may be carried off-premises)
7 = RM (supervised RF motion detector; sends fault and low battery signals, and sends periodic check-in
signals; panel ignores detector restore signals but automatically restores the zone to “ready” after a few
seconds; transmitter must stay within receiver's range)
NOTE: While the system is disarmed, faults from input type RM devices might not be seen on the keypad
display because the subsequent automatic restore can occur more quickly than the display is refreshed.
[∗] to continue

NOTES:
• For the built-in basic wired zones, the Input Type is automatically displayed as HW and cannot be edited.
• To change the input type of a previously programmed wireless device (type RF, UR, BR, RM) to a wired
zone (type AW), you must first delete the transmitter’s serial number.

For wireless transmitters, enroll the serial number and loop number as follows:
10 INPUT S/N: L 1. a. Transmit two open/close sequences. If using a button-type transmitter, press and release the button
twice, but wait about 4 seconds before pressing the button the second time. A022-4064 1
OR
b. Manually enter the 7-digit serial number printed on the label of the transmitter.
Press the [∗] key to move to the “L” position, then enter the loop number.
If desired, you can press the [C] key to copy the previously enrolled serial number (used when
programming a transmitter with several input loops). The cursor moves to the loop number position.

c. To delete an existing serial number, enter 0 in the loop number field. The serial number will change to
0's. If 0 was entered in error, simply re-enter tmber or press [#], and the serial number will
return to the display.
2. Press [∗] to continue. The system now checks for a duplicate serial/loop number combination.
– 8 –

If the serial/loop number combination is not a duplicate in the system, a display showing the serial number
10 INPUT S/N L and loop number entry appears.
A022-4064 1 [∗] to continue

This prompt will only appear if you answered “Yes” at the first prompt in this section.
XMIT TO CONFIRM The system will enter a confirmation mode so that the operation of the actual programmed input can be
confirmed. PRESS ✱ TO SKIP
Activate the loop input or button that corresponds to this zone.
[∗] to continue

If the serial/loop number transmitted does not match the serial number entered, a display showing the
Entd A022-4063 1 entered and the received serial/loop numbers appears.
Rcvd A022-4064 1 If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e.,
summary display does not appear), press the [#] key twice and then enter (or transmit) the correct serial
number.
[∗] to continue

If the serial number transmitted matches the serial number entered, the keypad will beep 3 times and
Zn ZT RC In: L a summary display will appear, showing that zone's programming. An “s” indicates that a
transmitter’s serial number has been enrolled. 10 03 10 RF: 1s
[∗] to accept the zone information and continue

If you want to program descriptors for zones now, enter 1 (Yes) and refer to the *82 Descriptor Programming
PROGRAM ALPHA? section for procedures. To program descriptors later, enter 0 (no).
[∗] to continue 0 = NO 1 = YES 0

If 0 (No) was entered at the Program Alpha prompt, the system will return you to the ENTER ZN NUM.
ENTER ZN NUM. prompt for the next zone.
When all zones have been programmed, enter 00 to quit. (00 = QUIT) 11

✱✱58 Expert Programming Mode Procedures (press ∗∗58 while in Data Programming mode) ✱✱ ∗∗

0 = no SET TO CONFIRM?
1 = yes (prompt appears after entering the serial and loop numbers to confirm each transmitter)
0 = NO 1 = YES We recommend that you confirm the programming of every transmitter.

A summary screen will appear, showing zone 1’s currently programmed values.
Zn ZT P RC HW: RT Enter the zone number being programmed, then press [∗]. In this example, zone 10 is being entered.
01 09 1 10 EL 1 01-06, 09-24, and 49-64 = zone number
[D] = for assigning wireless key programming templates (see Wireless Key Programming Templates section
in i/i); lets you choose from a series of preset templates for easy programming of wireless key zones
00 = quit (when all zones have been programmed, press “00” to quit this menu mode) Zn ZT P RC IN: L
[∗] to continue
10 – – – : –


A summary screen with the selected zone’s current programming appears.
Zn ZT P RC IN: L Begin programming zone information as follows:
Enter Zone Type (ZT; see Zone Type chart shown in *56 Menu Mode “Zone Type” prompt), Partition (P), 10 00 1 10 RF 1
Report Code (RC) 0-9 only (use *56 mode for hex codes), and Input Device Type (IN)* sequentially (Loop
Number (L) is entered at the next prompt).
• Use the [A] (Advance) and [B] (Back) keys on the keypad to move the cursor within the screen.
• Use the [C] key to copy the previous zone’s attributes.
* If HW (basic wired) or AW (Auxiliary) is entered for Input Device Type, the display will be similar to the
prompt shown, except that HW or AW will be under “IN”.

Press [∗] to save the programming and continue. If needed, press the [#] key to back up without saving.
For wireless devices (input types RF, UR, BR, RM), continue to the serial number/loop number prompt.
For wired devices, return to the initial summary screen prompt to begin programming the next zone.


Manually enter the serial number (found on the transmitter label), by entering the digits in the “X” locations,
10 INPUT S/N: L using the [A] (advance) or [B] (back) keys as required.
OR AXXX-XXX –
Transmit two open/close sequences. If using a button-type transmitter, press and release the button twice,
but wait about 4 seconds before pressing the button the second time.
If you want to copy the previous zone’s serial number, press the [C] key.
Zn ZT P RC In L
Press [∗] to advance to the loop number, then enter loop number.
10 03 1 10 RF: 1s
Press [∗] to accept the existing serial and loop number and continue to the “Confirm” prompt described in *56
Menu mode above.
If necessary, press [#] to back up and re-enter or edit the serial number.
If the serial number transmitted matches the serial number entered, the keypad will beep 3 times and a
summary display will appear, showing the programmed information for that zone.
Press [∗] to begin programming the next zone. See first “Summary Screen” prompt paragraph on previous
page.

– 9 – OFFON
Wireless Key Programming Templates (press the [D] key from *58 Menu mode Summary Screen display)
This procedure programs the wireless keys, but a key is not active until it is assigned to a user number (see System Operation section,
assigning attributes command in the Installation Instructions).

Enter desired template number 1–6 (see chart below).
TEMPLATE ? Press [#] if you want to return to *58 Menu mode Summary Screen.
If necessary, press [#] to back up and re-enter template number. 1–6 1
Press [∗] to continue to template display.

When [∗] is pressed, the selected template will be displayed.
L 01 02 03 04 Top line of display represents loop numbers, bottom line represents zone type assigned for each loop.
T 23 22 21 23 Press [∗] to accept template and continue.


Enter the partition in which the key is to be active.
PARTITION 1 = partition 1; 2 = partition 2; 3 = common partition
Press [∗] to continue. 1


The system will search for the highest available consecutive 4-zone group (the four zones in the case of the
ENTER START ZONE 5804), and display the lowest zone number of the group.
00 = QUIT 36 If you want to start at a different zone, enter the zone desired, and press [∗]. If that zone number is
displayed, the system has the required number of consecutive zones available, beginning with the zone you
entered. If not, the system will again display a suggested zone that can be used.
If the required number of consecutive zones is not available at all, the system will display “00”.
Press [∗] to accept and continue.

Manually enter the serial number printed on the label for the wireless key or press and release the button to
INPUT S/N L transmit its serial number.
AXXX-XXXX – Press [∗] to accept the serial number. The system will check for duplicate.
If necessary, press the [#] key to back up without saving, and re-enter the serial number.
Use the [A] key to move forward within the screen, and the [B] key to move backward.

If “Yes” was entered at the SET TO CONFIRM? prompt (first prompt following entry into the ∗58 Expert
XMIT TO CONFIRM Programming Mode), the display on the left will appear.
PRESS ✱ TO SKIP Confirm serial and loop numbers by activating the wireless key. Refer to the “Confirm” prompt described in
*56 Menu mode above for more information on confirming the serial number.
If the serial number transmitted matches the serial number entered, the keypad will beep 3 times and will
return you to the ENTER START ZONE NUMBER prompt to enter the starting zone for the next wireless key.
IMPORTANT: When confirmed, the key is not active until it is assigned to a user number (using the
assigning attributes command, attribute “4”). See System Operation section in Installation Instructions.
[∗] to skip confirm.

Wireless Key Predefined Default Templates
5804 5804BD/5804BDV Loop Function Zone Type Loop Function Zone Type
TEMPLATE 1 1 No Response 23 TEMPLATE 4 1 No Response 23
2 Disarm 22 2 No Response23
3 Arm Away213 Arm Away21
4 NoResponse234 Disarm22
TEMPLATE 2 1 NoResponse23TEMPLATE 5 1 NoResponse Disarm22ArmStay20
3 Arm Away 21 3 Arm Away 21 Arm Stay20 Disarm
TEMPLATE 3 1 24-hour audible7 TEMPLATE 6 1 24-hour audible7 Disarm222 ArmStay
3 Arm Away213 Arm Away21 ArmStay204 Disarm22

LOOP 3 LOOP 25800 Series Transmitter Input Loop Identification LOOP 2
(REED) (AUX.LOOP 4
CENTERYOU MUST LOOP
LOOP 2All of the transmitters illustrated below have one or more ENROLL 1
THIS LOOP 1 LOOP 3LOOP 1
LOOP 1BUTTON (TERMINALS) (AUX.
(PRIMARY)unique factory assigned input (loop) ID codes. Each of the RIGHT)
5802MN2inputs requires its own programming zone (e.g., a 5804's 5816
ENROLL AS
ENROLL AS "RF" 58175801 "UR" OR "RF"
ENROLL AS "RF"ENROLL ASfour inputs require four programming zones). "UR" OR "RF"

LOOP 3 LOOP 2
LOOP 2LOOP 4 LOOP 4 LOOP 2Note: For information on any transmitter not shown, refer (REED)YOU MUST LOOP 2 YOU MUST (REED)
ENROLL ENROLL
LOOP 1THIS THIS BUTTON LOOP 3to the instructions accompanying that transmitter LOOP 3BUTTON (TERMINALS) LOOP 1
(INTERNA
LOOP 1
SHOCK
LOOP 1for details regarding loop numbers, etc. SENSORSET
LOOP 3 (TERMINALS)HOUSE
(TERMINALS)CODE
5819 5819S (WHS & BRS)5804 5804BD
ENROLL AS "BR" ENROLL AS "RF" ENROLL AS "RF"ENROLL AS "BR"
LOOP 1
LOOP 2
(REED) LOOP 1
(MOTION)
5808 LOOP 1
ENROLL AS "RF" (TERMINALS)
(Green)ALTERNATE
(Red)
LOOP 1 POSITION (Yellow)
FOR LOOP 2
5890
5809 5816MN 5852 (GBD) ENROLL AS
ENROLL AS "RF" ENROLL AS "RF" ENROLL AS "RF" "RF" OR "RM"
– 10 –
VISTA48A 001 V0