Battery Reconditioning Guide

Description

https://allpreppersunited.com/battery-reconditioning-guide/ - In this Battery Reconditioning guide, discover the how and why reconditioning your old batteries is vital and the chemical in the process. Batteries that go uncharged for some extended period of time slowly become sulfated.

Informations

• Publié par: seorumer
• Publié le: 19 avril 2017
• Nombre de lectures: 1
• Langue: English

Extrait

Battery Reconditioning Guide

allpreppersunited.com/battery-reconditioning-guide/

Did you know that there is a way to recondition “dead” batteries so you won’t need to purchase another one as a replacement? This you can do via a battery regenerator or otherwise known as a battery reconditioner, desulphator, or pulse conditioning device.

And while you have that, we also can just know how to properly clean off the things in our batteries that are causing the problems.

Through these, we can effectively restore the capacities of ourlead-acid batteries, which would mean we would be able to extend their lifespan. Additionally, you must know, that theprocess of reconditioning is not the same as rechargingwhereas you aim to restore the charge for just a limited amount of time; with this, you recondition the battery back to its full capacity. This is a battery reconditioning guide you can base off of to unlock some not so common knowledge for all your survival or preparation needs.

Battery Reconditioning Guide: How it works?

Batteries that go uncharged for some extended period of time slowly become sulfated. Which is when lead-sulphur deposits then prop up on the lead plates inside of the battery. As a result of this, the battery no longer can charge fully to its initial capacity. These are where our regenerators or reconditioners come in. They send through the battery high-frequency pulses of electric current that flake off and eliminate any built up sulfate. And if you read on more, the regeneration process through these pulses in more detail kind of works like this.

Through the application of much higher voltages, you can dissolve the crystallized lead sulfate layer back into a solution. This running of a high voltage into a battery, however, would normally cause it to rapidly heat. This then giving in to the potential of an explosion via thermal runaway. Therefore, a battery reconditioner uses just enough short pulses of high voltages to reverse the crystallization process of the sulfate.

So we have our pulses, but you should also know that we can just simply properly clean in a special kind of way our batteries. That or we use chemicals in the stead of making pulses.

Battery Reconditioning Guide: Why?

You can do this for purelyeconomical reasons or for profit through reselling. The stockpile of dead batteries in your garage or backyard could make for worthy candidates. You potentially could restore all types of batteries from the deep cycle/gel type to the usual car battery using the method we will show to you here, right now. While not all batteries are the same, you can apply the same principles here to get you going there.

1/4

Battery Reconditioning Guide

The first thing to do in theprocess of reconditioningyour lead acid type battery that has sulfated due to old age or extended use would be an inspection of physical deformities or defects. These defects could hinder you from reconditioning your battery. They could be burnt connectors or melted plastic housing. Any physical signs that point as to why the battery does not work could prevent you from restoring it via reconditioning.

However, if no signs appear, then using this method of battery reconditioning potentially can indeed restore your battery if it no longer is functioning.

Warning: Do take caution when handing any chemicals involved. You will need safety precautions when reconditioning. These batteries contain potentially harmful acids. They can cause irritation or even negatively affect your health. Proper clothing and protective gear are advised as safety precautions when dealing with such chemicals.You are warned.

Have on hand lots of water and baking soda. You will start by washing thoroughly your battery. For any oils or stuck dirt, you may use a soft brush on the battery. For a really dirty battery, you can use dish soap to clean it. If you use baking soda, it will render any reacting battery acid harmless.

Through the use of a screwdriver, you then will need to pry the covers off your battery cell. As a safety precaution from the battery acid, you ought to wear old clothing or an apron. Acid is known to quickly chew through clothing.

So set the covers aside. You can use a small vacuum to suck out any large specks of dirt. Remember to also not let any dirt get into the cells of the battery. Wipe then the area around the holes of your cells with a damp paper towel.

Next, you must fill the cells with distilled water to a level just right above the plates. The water must be distilled. Using tap water may corrode your battery. And car batteries usually have a plastic cover over the plates. You must fill your water up to above the plastic cover top. Using a small water bottle can help avoid any messy or shaky

2/4

pouring of water. Do it slowly and prevent the water from overflowing.

Lastly then you will need to recharge your battery. You can do so with a professional radiant energy battery desulfator orDIY Battery Restorer.

Battery Reconditioning Guide: Using Chemicals

Step 1. Cleaning terminals

You will need to get rid of any corrosion or dirt of your terminals.

Step 2. Checking voltage

If your battery does not read 12 volts, then you have a problem with a cell.

Step 3. Testing cells.

Test each cell of your battery if it is weak or bad. Each cell must get a reading of at least 2 volts.

Step 4. Battery load test.

For this step, you are to test the load of your battery. Be mindful when doing so.

Step 5. Hydrometer test.

This is akin to the battery load test. You are going to use the hydrometer for step.

Step 6. Adding chemicals.

If it is determined that the battery is available for reconditioning, we now add some battery reconditioning chemicals.

The battery is then now to be charged for about 24 hours.

3/4

Battery Reconditioning Guide: Epsom Salt Alternative

The first thing you will need to do is determine if the battery would respond to reconditioning. The voltmeter must show 12 volts. The sweet pocket would be around 10 and 12 volts but anywhere below, it could be a waste of time.

Aquart of distilled must you heat to 150 degrees Fahrenheit. Additionally, dissolve 7 or 8 ounces of Epsom saltshalf in the water.

The cell caps of your battery you must then remove. If it were sealed, find the shadows plugs that would cover the cells of your battery. These you must drill through.

Drain then the fluid out of the battery. Furthermore, use then a plastic funnel to pour enough of your Epsom salt solution. This is so that you can have each cell of the battery properly filled.

The drill holes you must insert plastic plugs into. That or replace the battery caps and then shake your battery so that your Epsom salts are well spread out.

The battery you must then recharge slowly for 24 hours.

Thanks for reading and we hope you enjoyed this post. Please share it if you did! Thanks.

To speed up the whole process and simplify everything, then we recommend this unique method.

4/4