Range Rover : wipers and Washers

Hanson, Gary

Description

A combined underhood washer reservoir supplies the windscreen, tailgate glass and headlamp power wash. Three separate supply hoses are used with an electric pump for each facility. The reservoir incorporates a low level warning device. NOTE: See diagram. WASHER Remove Electrical Section 86 for wiring

Sujets

• Dandâ
• Manuel
• Automobile
• Land Rover
• Range Rover

Informations

• Publié par: LandRover
• Nombre de lectures: 282
• Langue: English

Extrait

Washer

 Disconnect the washer tubing from the pump. 2. Disconnect the electrical leads from the pump.

TAILGATE

Remove and refit

 WASHER PUMP

3. Remove two screws and withdraw the power wash pump.

WIPERS AND WASHERS

WIPERS AND WASHERS

RESERVOIR

Remove and refit

WASHER

NOTE: See El ect r i cal Sect i on 86 f or wi r i ng diagram.

3 . t he el ect r i cal l eads f r om t he pumps and the low level warning unit.

1. Loosen the hoseclamp and remove the power wash hose. 2. Di s connect t he t ubi ng f r om t he was her

WINDSCREEN

1.Disconnect the hose from the power wash

2. Disconnect the electrical leads from the pump.

Refitting

Refitting

POWER WASH PUMP

Remove and refit

Removing

 Reverse instructions1t o 4

1

The headlamp power wash is actuated when the windscreen washer control is used with headlamp low beam illuminated.

4. Reverse instructions1to 3.

Removing

A combined underhood washer reservoir supplies the windscreen, tailgate glass and headlamp power wash. Three separate supply hoses are used with an el ect r i c pump f or each f aci l i t y. The r es er voi r incorporates a low level warning device.

PUMP

WASHER

4. Remove the three securing bolts from below and withdraw the reservoir.

reservoir

Removing

Description

Headlamp power wash

WIPERS

AND

WASHERS

3. Pull the top of the pump away from its l ocat i on i n t he r es er voi r and r emove t he pump. Note the position of the sealing gasket in the reservoir.

Refitting

4. Reverse instructions 1 t o 3

WINDSCREEN WASHER JETS

Remove and refit

Removing

 Disconnect tubes from the jets.

     

2. Remove the locknut and washer securing jet to hood. 3.Remove jet.

Refitting

2

4. Reverse instructions 1 to 3.

WINDSCREEN

WASHER

Remove and refit

Removing

!

1 .

2 . 3 . 4 .

TUBES

RANGE  R O V E R

Disconnect tubing from reservoir pump. Disconnect tubing from washer jets. Disconnect tubing from threeway tee piece. Release tubing from edge clips.

Refitting

5. Reverse the removal procedure.

WIPER ARMS (WINDSCREEN)

Remove and refit

Removing

1. Hold back the small spring clip which retains t h e wi per ar m on t h e s h af t bos s u s i n g a suitable tool. 2. Gently pry off the wiper arm from the shaft boss.

Refitting

 1 9 8 7

3 . A l l o w t h e t omo t o r mo v et o t h e‘ par k’ position. 4. Push the arm on to the it on the splines so that the wiper blades are just clear oi the screen rail  s p r i n g  the retaining groove on the shaft boss. 6 . Operate the wiper on a wet screen to ensure that the blade does not overtravel at either end of its stroke.

WIPER ARM (TAILGATE)

Remove and refit

Removing

 Lift the wiper arm end cap to gain access to the wiper motor shaft. 2. Remove the wiper arm securing nut.

WIPERS AND WASHERS

3. Withdraw the wiper arm from the shaft.

Refitting

4. Allow the motor to move to the ‘park’ position.  Fit the wiper arm to the it on the splines so that the wiper blade is just clear of the screen surround. 6. Fit and tighten the securing nut. 7. Push the end cap back into position.  Check the correct of the wiper.

WIPER BLADES (WINDSCREEN

Remove and refit

Removing

AND TAILGATE)

1. Pull the wiper arm away from the glass.  Lift the spring clip and withdraw the blade lrom the arm.

Refitting

3. Reverse instructions 1 and 2.